RUT300 - INDUSTRIAL ETHERNET ROUTER
Rugged industrial fast Ethernet router comes with the benefits of RutOS, advanced security features, and a possibility to connect to the RMS. Five fast Ethernet ports, two configurable digital inputs/outputs, and a USB 2.0 allow to easily connect industrial machinery, office or retail equipment, and other devices to the internet.
INTERFACES
5 x Fast Ethernet ports (10/100 Mbps). 2 x Configurable digital Inputs/Outputs and USB 2.0
DURABILITY
Aluminum housing, which is capable to withstand harsh environments
VPN
Numerous VPN services including OpenVPN, IPsec, PPTP, L2TP & DMVPN, L2TP, DMVPN, Stunnel and others
RMS
For remote management, access & VPN services
ETHERNET
WAN
1 x WAN port 10/100 Mbps, compliance IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX
LAN
4 x LAN ports, 10/100 Mbps, compliance with IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX crossover
NETWORK
Routing
Static routing, Dynamic routing (BGP, OSPF v2, RIP v1/v2, NHRP)
Network protocols
TCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, FTP, SMTP, SSL v3, TLS, ARP, VRRP, PPP, PPPoE, UPNP, SSH, DHCP, Telnet, SMPP, SMNP, MQTT, Wake On Lan (WOL)
VoIP passthrough support
H.323 and SIP-alg protocol NAT helpers, allowing proper routing of VoIP packets
Connection monitoring
Ping Reboot, Wget Reboot, Periodic Reboot, LCP and ICMP for link inspection
Firewall
Port forward, traffic rules, custom rules
DHCP
Static and dynamic IP allocation, DHCP Relay, Relayd
QoS / Smart Queue Management (SQM)
Traffic priority queuing by source/destination, service, protocol or port, WMM, 802.11e
DDNS
Supported >25 service providers, others can be configured manually
Network backup
VRRP, Wired options, each of which can be used as an automatic Failover
Load balancing
Balance Internet traffic over multiple WAN connections
SSHFS
Possibility to mount remote file system via SSH protocol
SECURITY
Authentication
Pre-shared key, digital certificates, X.509 certificates, TACACS+, Radius, IP & Login attempts block
Firewall
Pre-configured firewall rules can be enabled via WebUI, unlimited firewall configuration via CLI; DMZ; NAT; NAT-T
Attack prevention
DDOS prevention (SYN flood protection, SSH attack prevention, HTTP/HTTPS attack prevention), port scan prevention (SYN-FIN, SYN-RST, X-mas, NULL flags, FIN scan attacks)
VLAN
Port and tag based VLAN separation
WEB filter
Blacklist for blocking out unwanted websites, Whitelist for specifying allowed sites only
Access control
Flexible access control of TCP, UDP, ICMP packets, MAC address filter
VPN
OpenVPN
Multiple clients and a server can run simultaneously, 27 encryption methods
OpenVPN Encryption
DES-CBC 64, RC2-CBC 128, DES-EDE-CBC 128, DES-EDE3-CBC 192, DESX-CBC 192, BF-CBC 128, RC2-40-CBC 40, CAST5-CBC 128, RC2-64-CBC 64, AES-128-CBC 128, AES-128-CFB 128, AES-128-CFB1 128, AES-128-CFB8 128, AES-128-OFB 128, AES-128-GCM 128, AES-192-CFB 192, AES-192-CFB1 192, AES-192-CFB8 192, AES-192-OFB 192, AES-192-CBC 192, AES-192-GCM 192, AES-256-GCM 256, AES-256-CFB 256, AES-256-CFB1 256, AES-256-CFB8 256, AES-256-OFB 256, AES-256-CBC 256
IPsec
IKEv1, IKEv2, with 14 encryption methods for IPsec (3DES, DES, AES128, AES192, AES256, AES128GCM8, AES192GCM8, AES256GCM8, AES128GCM12, AES192GCM12, AES256GCM12, AES128GCM16, AES192GCM16, AES256GCM16)
GRE
GRE tunnel, GRE tunnel over IPsec support
PPTP, L2TP
Client/Server instances can run simultaneously, L2TPv3, L2TP over IPsec support
Stunnel
Proxy designed to add TLS encryption functionality to existing clients and servers without any changes in the program’s code
DMVPN
Method of building scalable IPsec VPNs
SSTP
SSTP client instance support
ZeroTier
ZeroTier VPN client support
WireGuard
WireGuard VPN client and server support
Tinc
Tinc offers encryption, authentication and compression in it's tunnels. Client and server support.
MODBUS TCP SLAVE
ID range
Respond to one ID in range [1;255] or any
Allow Remote Access
Allow access through WAN
Custom registers
MODBUS TCP custom register block requests, which read/write to a file inside the router, and can be used to extend MODBUS TCP Slave functionality
MODBUS TCP MASTER
Supported functions
01, 02, 03, 04, 05, 06, 15, 16
Supported data formats
8 bit: INT, UINT; 16 bit: INT, UINT (MSB or LSB first); 32 bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC)
MODBUS DATA TO SERVER
Protocol
HTTP(S), MQTT, Azure MQTT, Kinesis
MQTT GATEWAY
MQTT Gateway
Allows sending commands and receiving data from MODBUS Master through MQTT broker
DNP3
Supported modes
TCP Master, DNP3 Outstation
MONITORING & MANAGEMENT
WEB UI
HTTP/HTTPS, status, configuration, FW update, CLI, troubleshoot, event log, system log, kernel log
FOTA
Firmware update from server, automatic notification
SSH
SSH (v1, v2)
TR-069
OpenACS, EasyCwmp, ACSLite, tGem, LibreACS, GenieACS, FreeACS, LibCWMP, Friendly tech, AVSystem
MQTT
MQTT Broker, MQTT publisher
SNMP
SNMP (v1, v2, v3), SNMP Trap
JSON-RPC
Management API over HTTP/HTTPS
MODBUS
MODBUS TCP status/control
RMS
Teltonika Remote Management System (RMS)
IOT PLATFORMS
Cloud of Things
Allows monitoring of: Device data, Mobile data, Network info, Availability
ThingWorx
Allows monitoring of: WAN Type, WAN IP
Cumulocity
Allows monitoring of: Device Model, Revision and Serial Number, WAN Type and IP
Azure IoT Hub
Can send device IP, Number of bytes send/received, Temperature, PIN count to Azure IoT Hub server
SYSTEM CHARACTERISTICS
CPU
QCA9531, MIPS 24kc, 650 MHz
RAM
64 MB, DDR2
FLASH storage
16 MB, SPI Flash
FIRMWARE / CONFIGURATION
WEB UI
Update FW from file, check FW on server, configuration profiles, configuration backup
FOTA
Update FW
RMS
Update FW/configuration for multiple devices at once
Keep settings
Update FW without losing current configuration
FIRMWARE CUSTOMIZATION
Operating system
RutOS (OpenWrt based Linux OS)
Supported languages
Busybox shell, Lua, C, C++
Development tools
SDK package with build environment provided
USB
Data rate
USB 2.0
Applications
Samba share, USB-to-serial
External devices
Possibility to connect external HDD, flash drive, additional modem, printer
Storage formats
FAT, FAT32, NTFS
INPUT / OUTPUT
Input
2 x Configurable digital Inputs. Digital input 0 - 5 V detected as logic low, 8 - 30 V detected as logic high.
Output
2 x Configurable digital Outputs. Open collector output, max output 30 V, 300 mA.
Events
Email, RMS
I/O juggler
Allows to set certain I/O conditions to initiate event
POWER
Connector
4-pin industrial DC power socket
Input voltage range
7 - 30 VDC, reverse polarity protection, voltage surge/transient protection
PoE (passive)
Passive PoE over spare pairs. Possibility to power up through LAN port, not compatible with IEEE802.3af, 802.3at and 802.3bt standards, Mode B, LAN1 Port, 9 - 50 VDC
Power consumption
Idle: 1.3 W, Max: 3 W
PHYSICAL INTERFACES
Ethernet
5 x RJ45 ports, 10/100 Mbps
I/O’s
2 x Configurable I/O pins on 4-pin power connector
Status LEDs
5 x ETH status, 1 x Power
Power
1 x 4-pin power connector
USB
1 x USB A port for external devices
Reset
Reboot/User default reset/Factory reset button
PHYSICAL SPECIFICATION
Casing material
Aluminum housing
Dimensions (W x H x D)
100 x 30 x 85 mm
Weight
229 g
Mounting options
DIN rail, flat surface placement
OPERATING ENVIRONMENT
Operating temperature
-40 °C to 75 °C
Operating humidity
10% to 90% non-condensing
Ingress Protection Rating
IP30
- MPN: RUT300
GTIN: 4779027312903
Changing your mind / purchasing the wrong product by mistake
If you change your mind after making a purchase, or realise you have purchased the incorrect item, you can enjoy the peace of mind that we offer a 7 day exchange policy.(excludesspecial order items).
If there is not a suitable product that can be exchanged for your returned item you will be offered a refund to your account based on the value paid at the time of purchase.
- to supply the correct product the incorrect product will first need to be returned to us;
- we will need to be notified within 7 days of purchase / delivery;
- the incorrect product supplied must be in a sealed / unopened condition.
Incorrectly supplied products
If you have been accidentally supplied the wrong product, F Digitalcan supply the correct product (where it is available) or issue a refund.
In order to supply the correct product, the incorrect product will first need to be returned to us. F Digitalcan arrange a return ticket to send the incorrect product back by courier.
In this scenario we will need to be notified within 7 days of purchase / delivery and the incorrect product supplied must be in resalable / unused condition.
Products damaged in transit
If your product has been damaged during transit to your delivery address an investigation will be conducted. Once the investigation has reached a conclusion and it is determined the product has been damaged in transit we will offer a refund.
Please contact us ASAP. We will then advise you to visit your nearest Australia Post Office so that they can investigate the damage. You will need to keep all packaging so that their team are able to make a fair assessment.
Products that are faulty upon arrival / first use
If the product you received is faulty upon arrival / first use, F Digitalwill either repair or issue a refund.
In order to repair or issue a refund for your faulty product, it will need to be returned to us so we can test and confirm that it is faulty.
All returns of this nature must be made within 7 days of purchase / delivery and we can arrange a return ticket to send the product back by courier.
Products that are faulty within the warranty period
If your product is faulty or has stopped working as intended and is still within the warranty period specified when you purchased your product, F Digitalwill repair or or issue a refund.
In order to repair or issue a refund for your faulty product, it will need to be returned to us so we can test and confirm that it is faulty. For some products you may also be able to contact the manufacturer directly to arrange a repair / replacement.
Returns of this nature can be made any time within the warranty period and it is your responsibility to cover any costs of returning the product to us.
Testing fees and return freight
If you return a product to us that is not faulty, you may be liable for a testing fee and freight charges to return the product to you.
Returns may take approximately 4 weeks to arrive back with our returns team in NZ to process.
Restocking fees
In some special circ*mstances, we may agree (at our discretion) to accept a return of a product that is not faulty. In these situations there will be a handling fee equal to at least 20% of the purchased price. Delivery, service and assembly fees are not refunded at all.
![Teltonika RUT300 Industrial VPN Router with 5 x Ethernet Ports, 1 x USB [RUT300] (1)](https://i0.wp.com/www.mydeal.com.au/content/themes/mydeal/images/icons/icon-guarantee.svg "Teltonika RUT300 Industrial VPN Router with 5 x Ethernet Ports, 1 x USB [RUT300] (1)"){kind=icon}
Shop with peace of mind
All marketplace products are covered by our MyDeal Refund Guarantee Learn More
![Teltonika RUT300 Industrial VPN Router with 5 x Ethernet Ports, 1 x USB [RUT300] (2024)](data:image/png;base64,iVBORw0KGgoAAAANSUhEUgAAAAEAAAABCAQAAAC1HAwCAAAAC0lEQVR42mP8/h8AAvMB+NzmkbcAAAAASUVORK5CYII=)